ATG-EA HEAT SENSOR

ATG-EA HEAT SENSOR

ATG-EA HEAT SENSOR APPLICATION The HOCHIKI America ATG-EA Sensor provides accurate temperature measurement data to the fire alarm control panel. This ...

126KB Sizes 0 Downloads 6 Views

ATG-EA HEAT SENSOR APPLICATION The HOCHIKI America ATG-EA Sensor provides accurate temperature measurement data to the fire alarm control panel. This sensor is particularly suited to environments where smoke detectors are unsuitable because of the precense of system or cooking fumes such as in a kitchen.

OPERATION

STANDARD FEATURES • Low Profile - Only 2.0" high, including base • Simple and reliable device addressing method • Uses the noise immune Digital Communication Protocol (DCP), which utilizes interrupts for fast response to fires • Adjustable threshold temperature 135°F - 150°F (determined by panel)

SPECIFICATIONS Operating Voltage Standby Current Alarm Current Transmission Method

17-41 VDC 350μA 500μA DCP - Digital Communication Protocol Maximum Humidity 95% RH Non-Condensing UL Ambient Installation 32°F to 115° F Temperature Range (0° C to 47° C) Operating Temperature 135°F to 150° F Range (57.2° C to 65.6° C) Color & Case Material Bone PC / ABS blend Weight 3.2oz (4.9 oz. with 4" base) Bases 4" YBN-NSA-4 6" HSB-NSA-6

The ATG-EA Heat sensor incorporates a highly linear thermistor circuit, with the thermistor mounted externally. The specially designed cover protects the thermistor while allowing maximum air flow. The thermistor circuit produces a voltage proportional to temperature which is scaled, and transmitted as a digitally encoded value to the control panel. When the ambient temperature exceeds a pre-programmed threshold (fixed temperature), the sensor transmits an interrupt to the control panel indicating a fire alarm. The fire alarm control panel can adjust the sensor threshold for different Standard's requirements. Up to 127 devices are permitted on each loop. A sensor address can be set by a hand-held programming unit. The sensor mounts to an electronics free base and incorporates a locking mechanism secure installation. The base provides mounting slots, terminals for field wiring, and a third contact for a remote indicator/LED. The sensor incorporates dual LED's for easy viewing of sensor status.

ENGINEERING SPECIFICATIONS Heat sensors are installed in accordance with NFPA (National Fire Protection Association) 72, the UL Listed Spacing Requirements and the rules and regulations set forth by the local authorities having

PRODUCT LISTINGS

3022559

MEA

S2966 Specifications subject to change without notice.

Hochiki America Corporation 7051 Village Drive, Suite 100 Buena Park, CA 90621-2268 Phone: 714/522-2246 Fax: 714/522-2268 Technical Support: 800/845-6692 or [email protected]

NYC Department of Building 284-91-E Vol. 4

California State Fire Marshal 7270-0410:147 Continued on back.

Find latest revision at www.hochiki.com

F0023

03/2011

ENGINEERING SPECIFICATIONS, continued jurisdiction. Automatic heat sensors shall be Underwriters Laboratories listed. The base shall permit direct interchange with the HOCHIKI America AIE-EA ionization type smoke sensor, and the ALG-V photoelectric smoke sensor. The vandal-resistant, security locking feature shall be used in those areas as indicated on the drawing. The locking feature shall be optional and can be implemented when required. It shall be possible to perform a functional test of the sensor without generating heat. The test method shall simulate the effects of heat on the device to insure testing of internal circuitry.

BASES The HOCHIKI America HSB-NSA-6 and the YBN-NSA-4 mounting bases are electronic free and are a simple rugged design with screw terminals for wiring connections. A common mounting base allows sensor interchange and maintains loop continuity when sensors are removed. A simple anti-tamper head locking system is provided which is enabled by removing a small plastic tab on the back of the sensor. Once locked, the head can be removed using a small diameter screw driver. (DIAGRAM OF 2 BASES HERE)

HSB-NSA-6 Base

YBN-NSA-4 Base

TYPICAL WIRING DIAGRAMS

NOTE: Fire alarm control panel compatibility is required for DCP products. State-of-the-art communications protocol, DCP, allows system components (DCP sensors AIE-EA, ALG-V and ATG-EA, bases and modules), to be used concurrently in a system's signal conditioning loop. Hochiki America Corporation ATG-EA

Specifications subject to change without notice.