CriCket Floor Stand - Schacht Spindle Company

CriCket Floor Stand - Schacht Spindle Company

0 CriCket Floor Stand Assembly InstructIons For 10" AnD 15" stAnDs 67 49 36 0 42 5 92 4 0 76 81 31 90 7 0 36 Find out more at schachtspindle.co...

NAN Sizes 0 Downloads 0 Views

0

CriCket Floor Stand

Assembly InstructIons For 10" AnD 15" stAnDs

67 49 36 0

42 5 92 4

0 76 81 31

90 7 0 36

Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO 80301 p. 303.442.3212 f. 303.447.9273 49 24 0 70

© 20120 Schacht Spindle Company, Inc. 42 59 49

11.12

Cricket Floor Stand Assembly Instructions

Tools

Parts

1 – cross brace (15") or 2 – cross braces (10") 2 – legs 2 – bases 4 – barrel nuts (15") or 8 – barrel nuts (10") 2 – knobs 2 – washers 2 – Allen (hex) head screws 2 – 7/8" screws 4 – 2" screws 1 – drilling template (10")

Phillips screwdriver Drill and 3/16" drill bit Allen wrench 5/32" (included) Scissors Wood screw (pointed end, any size) Hammer Scrap wood Masking tape (optional) slanted top edge drilling template

cross brace(s)

legs

bases bronze insert

assemble LEGs and bases

■■ Orient a leg with the top edge slanting toward you. At the bottom of the leg, from the left side, insert a 7/8" screw into the upper hole. ■■ Place a base to the right of the leg, with the bronze insert in the base facing away

from the leg. Attach the leg to the base by securing the screw into the bronze insert in the base. ■■ Perform these steps for the other leg, inserting the screw from the right side and placing the base on the left.

right leg - outside

left leg - inside

–2–

attach the cross brace

■■ Insert barrel nuts into the holes in the cross brace, with the slots in the barrel nuts parallel to the long side of the brace. Hold the barrel nuts in place with masking tape.

these bolts with a washer and knob. Tighten the knobs until they are about 3/4" from the loom sides. ■■ Skip to the section “All Cricket Looms.”

10" CRICKET LOOMS

If your Cricket Loom has two holes in each side just in front of the heddle block, skip to the section on installing the cross brace.

barrel nut with slot parallel to cross brace

heddle block

■■ Insert 2" screws into the holes at the bottom of the leg and through the base. ■■ Align the cross brace with the screws at the bottom of the base. ■■ Secure the cross brace to the base by tightening the screws into the barrel nuts. ■■ Remove the masking tape from the cross brace.

15" CRICKET LOOMS

■■ On each side of the loom, remove the rear bolt (closest to the warp beam) holding the cross brace. Replace these bolts with the Allen-head screws. Using the Allen wrench, tighten the screws into the barrel nuts until the heads are against the loom sides. ■■ On each side of the loom, remove the front bolt holding the cross brace. Replace

holes

Drill holes for THE CROSS BRACE

Factory Service: If you would like to send us your loom sides, we would be happy to drill your sides for you. Just mail them to us and enclose a check for $20.00. Service for continental U.S. only. Please be sure to enclose your name, mailing address, daytime phone number, and email address.

■■ Carefully cut out the template along the outside lines. ■■ Align the template with the left loom side. Use masking tape to hold it in place. ■■ Use a screw to poke a small hole through the template at the center of the x’s. Gently tap the screw with a hammer through the x’s to mark the hole placement. ■■ Work on the corner of a work table. Place the scrap wood under the loom side at the points to be drilled.

Do not work on a good table as it is possible to damage it when drilling. It is important to use the scrap wood

–3–

to prevent damage to the loom side when drilling. ■■ Use a 3/16" drill bit and drill straight down with firm pressure. Drill all the way through the loom side and into the scrap wood. ■■ Reverse the template and repeat for the right side.

ALL CRICKET LOOMS

■■ Place the loom between the stand legs. Slide the head of the Allen-head screw in the rear slots and the threaded part of the knob into the front slots. Make sure that the washers are next to the knobs on the outside of the stand.

Install the cross brace

■■ Insert barrel nuts into the holes in the cross brace, with the slots in the barrel nuts parallel to the long side of the brace. Hold the barrel nuts in place with masking tape. ■■ Align the cross brace between the loom sides. ■■ Insert the Allen-head screws into the rear holes on each side and into the cross brace. Tighten the Allen-head screw into the barrel nut until the head of the screw is against the loom side. Repeat for the other side.

■■ Move the front of the loom up or down then tighten the knobs when you have the loom at the desired angle. ■■ When you remove the loom from the stand, tighten the knobs to the loom side to secure the cross brace.

■■ Put a washer on a knob, and insert the knob into a front hole. Tighten the knob into the barrel nut until the knob is about 3/4" from the loom side. Repeat for the other side. ■■ Remove the masking tape from the cross brace.

–4–