O2 Oxygen Measurement Guide

O2 Oxygen Measurement Guide

O2 MEASUREMENT GUIDE By Erich K. Springer R THE MEASURE OF EXCELLENCE TM Important Notice Reproduction of any part of this booklet in any form ...

5MB Sizes 1 Downloads 15 Views

O2 MEASUREMENT GUIDE

By Erich K. Springer

R

THE MEASURE OF EXCELLENCE

TM

Important Notice

Reproduction of any part of this booklet in any form whatsoever without the express written consent of HAMILTON Bonaduz AG is forbidden. The contents of this booklet are subject to change without notice. Technical changes reserved. All efforts have been made to ensure the accuracy of the contents of this booklet. However, should any errors be detected, HAMILTON Bonaduz AG would greatly appreciate being informed of them. The above notwithstanding, HAMILTON Bonaduz AG can assume no responsibility for any errors in this manual or their consequences. Copyright © 2009 HAMILTON Bonaduz AG, Bonaduz Switzerland. All rights reserved.

Wichtiger Hinweis

Die Reproduktion irgendeines Teils dieses Handbuchs in jeder beliebigen Form ist ohne die ausdrückliche schriftliche Zustimmung der HAMILTON Bonaduz AG untersagt. Der Inhalt dieses Handbuchs kann ohne vorherige Ankündigung geändert werden. Technische Änderungen vorbehalten. Es wurde grösstmögliche Sorgfalt auf die Richtigkeit der Informationen in diesem Handbuch verwendet. Sollten dennoch Fehler entdeckt werden, würde sich die HAMILTON Bonaduz AG freuen, darüber informiert zu werden. Ungeachtet dessen kann die HAMILTON Bonaduz AG keine Haftung für etwaige Fehler in diesem Handbuch oder deren Folgen übernehmen. Copyright  2009 HAMILTON Bonaduz AG, Bonaduz Schweiz. Alle Rechte vorbehalten.

Page 1

Table of Contents 1. INTRODUCTION.......................................................................................................................... 3 2. OXYGEN...................................................................................................................................... 4 3. THE DISCOVERY OF OXYGEN ................................................................................................. 5 3.1 The Phlogiston Theory .........................................................................................................5 3.2 Carl Wilhelm Scheele ...........................................................................................................6 3.3 Joseph Priestley ...................................................................................................................7 3.4 Antoine-Laurent de Lavoisier ...............................................................................................8 4. THE PERIODIC TABLE OF THE ELEMENTS .......................................................................... 10 Drawing: The Periodic Table ....................................................................................................11 5. THE ATMOSPHERIC PRESSURE............................................................................................ 12 Table 1: Composition of the Atmosphere .................................................................................13 6. PASCAL’S PRINCIPLE............................................................................................................. 15 Table 2: Conversion Factors between Different Units of Pressure ..........................................16 7. SATURATED VAPOUR PRESSURE ........................................................................................ 16 Table 3: Saturated Vapour Pressure of Water (at different temperatures)...............................17 8. PARTIAL PRESSURE............................................................................................................... 18 8.1 Dalton’s Law.......................................................................................................................18 8.2 Partial Pressure..................................................................................................................18 8.3 Absolute Pressure ..............................................................................................................19 Table 4: Altitude versus Atmospheric Pressure .......................................................................19 9. OXYGEN CONCENTRATION IN WATER................................................................................. 19 Table 5: α-values for Oxygen in Water.....................................................................................22 Table 6: Saturated oxygen concentration ................................................................................23 10. OXIDATION - REDUCTION (REDOX)..................................................................................... 25 11. THE MEASURING PRINCIPLE ............................................................................................... 26 12. THE MEMBRANE-COVERED CLARK DISSOLVED OXYGEN SENSOR ............................. 28 13. CALIBRATION ........................................................................................................................ 30 13.1 Sensor Zero Calibration ...................................................................................................30 13.2 Sensor Slope Calibration .................................................................................................31 13.2.1 Calibration in Water............................................................................................................... 31 13.2.2 Calibration in Air.................................................................................................................... 31 13.2.3 Calibration with a Calibration Solution .................................................................................. 33

14. INFLUENCE OF SALINITY ..................................................................................................... 33

Page 2 15. THE HAMILTON DO SENSORS ............................................................................................. 33 15.1 The OXYSENS Dissolved Oxygen Sensor ......................................................................35 15.1.1 OXYSENS Technical Data ................................................................................................... 35

15.2 The OXYFERM Dissolved Oxygen Sensor ......................................................................36 15.2.1 OXYFERM Technical Data ................................................................................................... 37

15.3 The OXYGOLD Dissolved Oxygen Sensor ......................................................................37 15.3.1 OXYGOLD G Technical Data ............................................................................................... 38 15.3.2 OXYGOLD B Technical Data................................................................................................ 39

16. STABILISATION TIME – POLARIZATION MODULES .......................................................... 39 17. MAINTENANCE OF THE HAMILTON OXYGEN SENSORS.................................................. 40 17.1 OXYSENS ........................................................................................................................40 17.2 OXYFERM........................................................................................................................40 17.3 OXYGOLD G & B .............................................................................................................41 18. CONNECTION TO VARIOUS PROCESS METERS/CONVERTERS/TRANSMITTERS ........ 42

COPYRIGHT This book is copyright protected. No part of this book may be reproduced or transmitted in any form or by any means, electronically or mechanically, including photocopying, recording or by any other information or storage or retrieval system without permission by HAMILTON.

Page 3

Dissolved Oxygen Measurement Theory and Practice by Erich K. Springer

1. Introduction Oxygen is the most important gas for plant and animal life on our planet earth. Without oxygen, there is no life on land or in water. As oxygen is easily soluble in water it makes life in rivers, lakes and oceans possible. Water owes its content of dissolved oxygen by the fact that it is continuously exposed to the atmospheric air, and the amount of soluble oxygen in water is therefore determined by the partial pressure of oxygen and the temperature. In ecological systems like seas, rivers and lakes the oxygen content has to be monitored in order to determine the state of pollution in these systems. In the treatment of domestic and industrial waste water a high amount of oxygen is required by the micro-organism to decompose organic waste; on the other hand the oxygen content in boiler water and feed water systems must be kept as low as possible in order to minimise the corrosion danger in boiler and pipe walls. To measure the dissolved oxygen amount accurately and continuously and to take the required action will save the industry billions of Rand, Dollars, Yen, Euros and Pounds annually, to name just a few currencies. The purpose of this booklet is to provide the basic knowledge of the dissolved oxygen measurement in a brief and understandable form. The author’s task is fulfilled when this booklet leads to a successful application of a dissolved oxygen measurement. First edition November 2008

Acknowledgements Many thanks goes to Dirk Tillich for providing me with special information and material. I also want to thank Dr. Hannes Bühler of HAMILTON, for reading my manuscript, adviced me on certain subjects and corrected the odd mistakes. Last, but not least, I want to thank my loving wife for her patience and understanding for so many lonely evenings. Erich K. Springer

Page 4

2. Oxygen

Electron-

Oxygen is a non-metallic chemical element with the chemical symbol O and the atomic number 8. It occupies place 8 under group 16 (VIB) in the Periodic Table of Elements (see page 11) and its atomic mass is 15,9994. Under atmospheric pressure and temperature, oxygen is a colourless, odourless and tasteless gas in a diatomic molecular form O2.

Proton+ Nucleus Neutron K-shell L-shell

8

O=O By combining more than one unpaired electron at a time, a double covalent bond is formed. Oxygen atoms form a double covalent bond and the resulting molecule O2 is very stable.

Atomic mass

15,9994

O

Atomic number Symbol Name

Oxygen

The Oxygen Atom

Another form of elemental oxygen is ozone (O3), which is a triatomic molecule, consisting of three oxygen atoms. The ozone molecule is much less stable than the diatomic O2. Close to the earth surface ozone is toxic with harmful effects on the respiratory systems of humans and animals. An ozone concentration of more than 125 parts per billion (ppb) is regarded as “unhealthy” by the World Health Organisation. Ozone in the upper atmosphere (15 to 45 km), forms a thin, protective layer around the earth that filters potentially damaging ultraviolet light from reaching the earth’s surface. Some pollutants in the atmosphere have a detrimental effect on this ozone layer.

116,8° The Ozone (O3) molecule

After hydrogen and helium, oxygen is the third most abundant element in the universe. In stars like the sun its formation is part of the fuel cycle that provides their energy. On the planet earth oxygen is the most abundant element: 85,7 % by weight in seawater (88,8 % of pure water is oxygen) 46,6 % by weight in the earth’s crust 20,95% by volume in the lower atmosphere. Our planet earth has an unusual high level of oxygen gas (O2) in its lower atmosphere compared with other planets in our solar system. The value of nearly 21% in air lies midway between two extremes that would make life on earth impossible for humans. If it were below 17% we could not breath anymore, if it were above 25% all organic material would be highly flammable.

Page 5 Oxygen in the biosphere is essential for all forms of life since it is a constituent of DNA and of almost all other biologically important compounds. It is even more important in the processes of respiration, the means by which all living creatures derive the energy needed to sustain life. It is well known that the human brain must have oxygen to function and that, if denied oxygen, it will be damaged within minutes. Oxygen circulates through the ecosystem and the biosphere in various forms. It is free in the air and dissolved in water. Certain lower order plants and all animals use oxygen to respire and return it to air and water as carbon dioxide (CO2). CO2 is then taken up by algae and terrestrial green plants and converted into carbohydrates during the process of photosynthesis, combining it with water to create sugars and oxygen molecules. Free oxygen is returned to air and the cycle starts again. Almost all the free oxygen present in the atmosphere is the result of photosynthesis. The waters of the world are the main oxygen generators of the biosphere; their algae are estimated to replace about 90 % of all oxygen used. Oxygen has an 2 - 6 electron configuration with a valence of 2. This makes it highly reactive and capable of combining with all elements except the noble gases, and with most compounds under the influence of temperature and light. The chemical process is called “oxidation” and the resulting compounds are “oxides”. A very rapid form of oxidation is the burning or combustion process. Other properties of oxygen:

Boiling point: -182,97 °C (at 1 atm) Melting point: -218,76 °C (at 1 atm) Critical point: -118,9 °C (at 1 atm) Density: 1,429 g/l at 1 atm and 0°C Pure oxygen is 1,1 times heavier than air Liquid oxygen is strongly magnetic Liquid and solid oxygen have a pale blue colour

3. The Discovery of Oxygen 3.1 The Phlogiston Theory Johann Joachim Becher (1635 - 1682), a German alchemist and physician, proposed in 1669 that substances are composed of three types of earth: “terra fluida” is the mercurial element, which contributes fluidity and volatility; “terra lapida” is the solidifying element, which produces the binding quality; and the third element is “terra pinguis” (fatty earth), which gives material substances its combustible qualities. This is the principle of inflammability. Wood, for instance, consists of ash and “terra pinguis”. When wood was burned the wood would be converted to ash and the “terra pinguis” was released. Later, Georg Ernst Stahl, (1660 - 1734), another German alchemist and physician, adopted the idea, but changed the name of “terra pinguis” to “Phlogiston” - from the Greek phlogios (fiery). Hence the name “Phlogiston Theory”. He modified the theory and stated that all combustible materials were composed of two parts. One part, the “phlogiston”, was given off when the substance containing it was burned. The other part, the “de-phlogisticated” part was thought to be its true form, its “calx”. Stahl also included the calcination and corrosion of metals. When the metal was heated, “phlogiston” was set free and the “calx” remained. Highly combustible materials, such as coal, where made mostly of “phlogiston” while non-combustible substances, such as iron, contained very little. Air did not play a role in the “phlogiston theory” and no initial quantitative experiments were conducted to test the idea. The “phlogiston theory” was based only on observation of what happened when something burned.

Page 6 For almost a century the false doctrine of “phlogiston” obscured the brain of all alchemists. Nobody ever had the idea that it was actually the reverse process: During combustion a gas is combining with the burned substance. 3.2 Carl Wilhelm Scheele Carl Wilhelm Scheele was born on the 9th of December 1742 in Stralsund, Germany, which at that time was the capital of Swedish occupied Pomerania. Scheele was the seventh of eleven children, and there was no money for his education. Although, without formal training in chemistry, he became one of the greatest experimental chemists, and perhaps the most unfortunate scientific discoverer, of the 18th century. Scheele taught himself chemistry while apprenticed (1757 1765) to an apothecary in Göteborg, Sweden. Later he worked as a pharmacist in Malmo, in Stockholm, and in Uppsala, till he bought his own pharmacy in Köping, (1775) where he remained for the rest of his life.

Carl Wilhelm Scheele (1742 - 1786)

This industrious, self-taught chemist, without a high-school and academic education, is now accredited with the discovery and identification of seven chemical elements and compounds, more than any other scientist discovered before him or since.

In 1772, while experimenting with a mixture of calcium nitrate and sulphuric acid, Scheele observed that a colourless gas escaped when the mixture was heated. He collected the gas in a glass cylinder and when he lit a candle within the cylinder, he saw that the candle burned much brighter than normal. From this and similar experiments he deducted that air consists of two gases, one that supports combustion and the other that prevents it. He named the former “fire air” and the later “rotten air”. Scheele experimented with this “fire air”. He discovered various different ways how to produce “fire air”; from nitric acid, potassium nitrate, manganese dioxide, mercuric oxide and many more. Scheele discovered that “fire air” was not only necessary for burning but for breathing as well. He put rats and mice, flies and bees, one after another, into jars and watched their behaviour. Every time the result was as he suspected: after the “fire air” was consumed, the creatures died. But Scheele failed to recognise “fire air” as a chemical element (namely oxygen), without which no life is possible on this planet. The “phlogiston theory” of Stahl was a barrier, which prevented Scheele from understanding this vital and essential fact of life. Scheele wrote an account of his discovery in a manuscript he titled “Treatise on Air and Fire”, which he sent to his publisher in 1773. However, that document was not published until 1777. Because of the delay in publishing the results of his experiments, Scheele became the unaccredited discoverer of oxygen.

Tools Carl W. Scheele used during his experiments to analyze the composition of air

Page 7 In early 1786 Carl Wilhelm Scheele fell seriously ill. The symptoms suggest mercury poisoning. He died, as a victim of his chemical experiments after only 44 years of age, on the 21st of May 1786. 3.3 Joseph Priestley Joseph Priestley was born on the 13th of March 1733 in Fieldhead, Yorkshire, England. Joseph was the first of six children. He was educated at Daventry Academy and trained as a minister of the Dissenting Church of England. Besides his radical theological work and writings, Priestley became interested in physical science, mainly electricity and chemistry. But Priestly was first and foremost a Unitarian minister and, to begin with, practised science only as a hobby. Priestley attended lectures and demonstrations on practical chemistry given in 1763 – 1765 by the surgeon Matthew Turner.

Joseph Priestley (1733 - 1804)

In 1766 he met the American statesman Benjamin Franklin in London, who encouraged him to conduct experiments in the new science of electricity. A year later Priestley wrote his famous work “The History and Present State of Electricity”. Priestley discovered that charcoal was conductive and noted the relationship between electricity and chemical change. More and more his interest changed towards chemistry. He studied “airs”, as gases were then called.

Joseph Priestley’s most famous discovery occurred on the 1st of August 1774 when he heated red “calx” of mercury (mercuric oxide) in a glass vessel by focusing the rays of the sun through a 300 mm diameter lens on to it. He found that silvery drops of mercury began appearing in amongst the red “calx”. Simultaneously the decomposing “calx” emitted a colourless gas. Priestley collected the gas in a flask and lit a candle in it. He noted that the candle was burning “with a remarkably vigorous flame. … But to complete the proof of the superior quality of this air, I introduced a mouse into it; and in a quantity in which, had it been common air, it would have died in about a quarter of an hour, it lived … a whole hour.” Priestley, as his contemporary Scheele, believed in the “phlogiston theory”, which blurred his intellect and scientific judgement. He named the “new air” he discovered, “dephlogisticated air” because objects burned so easily in its presence, it meant they rapidly released their “phlogiston”. He believed that ordinary air became saturated with “phlogiston” when it could no longer support combustion or life. As Priestley, during a visit to Paris later in 1774, passed on his discovery of “dephlogisticated air” to the greatest chemist of the era, Antoine-Laurent de Lavoisier, and published his findings in 1775 in a work titled “Experiments and Observations on Different Kinds of Air”, he received the credit for the discovery of oxygen. Priestley’s observation that light was important for plant growth and that green plants gave off “dephlogisticated air” became the foundation for systematic studies on photosynthesis by other scientists.

Page 8 The radical and liberal theological ideas of Priestley plus his support for the principles of the French Revolution angered the British public. On the second anniversary of the fall of the Bastille prison (14th of July 1791) a paid mob went on the rampage and burned and looted the house, laboratory and church of the dissenter Priestley. Priestley escaped in time and three years later, in 1794, fled England to settle in Northumberland, Pennsylvania, USA. Here he died on the 6th of February 1804. He was the last champion of the “phlogiston theory”. 3.4 Antoine-Laurent de Lavoisier Antoine-Laurent de Lavoisier was born into a wealthy, upper-class family in Paris on the 26th of August 1743. His grandfather and father were both successful lawyers, his mother was the daughter of a rich advocate. She died when Antoine was five years old. He was brought up in his grandmothers house by his unmarried aunt Marie, sister of his mother. Both women very much spoilt little Antoine, money was never a question.

Antoine-Laurant de Lavoisier with his wife Anne-Marie

When he was eleven years old, he attended the famous Collège Mazarin, the best institute in France at that time. At seventeen Lavoisier entered the School of Law at the Sorbonne, the oldest university of the world and at the age of 21 he graduated as a Bachelor of Law and qualified as Licentiate a year later.

After completing his study of law, it was science, not law, that called. Lavoisier attended courses in astronomy and mathematics, botany, geology and “alchemy” (chemistry was not yet an academic subject). He became known in scientific circles initially, when he was awarded a gold medal, presented by the president of the Royal Academy of Science, for an essay on the best way to light the streets of a large town at night. He became a member of the Royal Academy of Science at the young age of 25. Lavoisier was probably one of the most educated men of his time, and he was rich. There was no need for him to earn money. Young Lavoisier became more and more interested in the newly emerging scientific subject “Chimie”. He was fascinated by the mystery of chemistry, a subject which was still in its infancy. Chemistry had not yet grown out of the alchemical arts of making gold from mercury, it was still dominated by Aristotle’s four elements: water, earth, air and fire. Lavoisier became the father of modern chemistry; he was the first scientist who introduced quantitative procedures into chemical investigations, he formulated the principle of the conservation of matter in chemical reactions, he clarified the distinction between elements and compounds, and he was instrumental in devising the modern system of chemical nomenclature. Yet he was not a single-minded pioneer. During his brief fifty years of life he not only adopted a modern approach to chemistry, but also held simultaneously several top-level public offices in the French government. He contributed technological advances in ballooning, the mineralogical mapping of France, urban street lighting, the Paris water supply, the efficiency of gunpowder and a full-scale model farm. He was a member of the commission appointed to secure uniformity of weights and measures throughout France. The report of that commission led to the adoption of the metric system.

Page 9 In 1768 he became a member of the “Ferme Générale”, a governmental tax collecting agency. He introduced a tax reform and in 1788 build a wall around Paris in order to make the custom collection more efficient. This turned out to be the worst decision of his life as it made him a hated enemy by the lower classes. In 1772, after various other chemical investigations, Lavoisier turned his attention to the much discussed problem of combustion. He conducted an experiment heating lead in a sealed vessel containing a limited supply of air. At the beginning of the heating process the surface of the lead formed a layer of calx (lead oxide), and then it stopped doing so. Lavoisier now weighed the entire apparatus (containing lead, calx, air etc.), and found that it weighed exactly the same as it had done before being heated. Next he weighed the lead and its coating of calx – and found that this weighed more than the metal had previously weighed. But if the metal had gained weight, then something else in the vessel must have lost a similar amount of weight, and this could only be the air. Lavoisier’s experiment proved that when metal turned into its calx, this had nothing to do with the loss of some mysterious phlogiston. He had shown that the metal in fact combined with a material substance which had weight, and that material substance consisted of a portion of the air. It was now, in 1774, that Priestley arrived in Paris, and demonstrated to Lavoisier the new gas he had discovered, which he called “dephlogisticated air”. When Priestley demonstrated his “dephlogisticated air”, Lavoisier immediately grasped the far-reaching significance of this discovery. As soon as Priestley returned to England, Lavoisier experimented with a burning candle floating in a bowl of water. He placed an upturned glass jar over the candle and observed that, when the candle burned the water always rose to occupy one fifth of the jar. Air obviously consisted of two gases, in proportion of one to four. The one fifth which was used in combustion was Priestley's “dephlogisticated air”. Through his experiments, Lavoisier demonstrated that burning is a chemical reaction, combining a substance with the new found gas. He disproved the “phlogiston theory” and paved the way for a correct analysis of chemical compounds. Lavoisier decided to rename this elemental gas “oxygen” - from the Greek “oxy” - meaning “acid” and “gen” meaning “generator” or “producer”. Lavoisier mistakenly thought that oxygen was present in all acids. With the storming of the Bastille on the 14th of July 1789 the French revolution had begun and found Lavoisier in an extremely tricky situation. As a scientist he had done as much as anyone to promote enlightened reform, but he was also a member of two institutions which were strongly linked with the ancien régime: the Académie des Sciences and the hated Ferme Générale. For four years Lavoisier could survive, but in November 1793, when the terror was in full swing, Lavoisier was arrested. On the 8th of May 1794 Lavoisier was brought before the revolutionary tribunal, tried within hours, sentenced to death and guillotined on the same day. When his friend, the celebrated French mathematician Joseph-Louis Lagrange, heard the news, his comment made a bitter epitaph: “Only a second to cut off that head, and a hundred years may not give us another like it.

Page 10

4. The Periodic Table of the Elements In early 1869 Dmitri Mendeleyev (1834-1907), a Russian chemist, published his historic paper “A Suggested System of the Elements”. In this paper the design of the first “Periodic Table of the Elements” was introduced to the chemists of his time. Mendeleyev clearly established the relationship between the properties of the elements and their atomic weight. In Mendeleyev’s own words “… there must be some bond of union between mass and the chemical elements; and as the mass of a substance is ultimately expressed … in the atom, a fundamental dependence should exist … between the individual properties of the elements and their atomic weight. But nothing … can be discovered without looking and trying. So I began to look about and write down the elements with their atomic weights … and this soon convinced me that the properties of the elements are in periodic dependence upon their atomic weight; and although I have had no doubts about some obscure points, yet I have never once doubted the universality of this law, because it could not possibly be the result of chance.” (Principles of Chemistry; by Dmitri Mendeleyev, 1868).

Dmitri Mendeleyev

The Original Periodic Table of the Elements

In a modern table the elements are arranged horizontally in order of increasing proton numbers. The elements fall into 18 vertical columns, known as groups. Going down a group, the atoms of the elements all have the same outer shell structure, but an increasing number of inner shells, therefore all elements in a group have the same chemical activity. Today there are 115 elements listed in the Periodic Table of Elements, of which the last four have not yet been named. The Dmitr Mendeleyev Statue in St. Petersburg, Russia

Page 11

Drawing: The Periodic Table

Page 12

5. The Atmospheric Pressure The dissolved oxygen in water is the gaseous oxygen (O2) dissolved in water and must not be mistaken for the bound oxygen as in the water molecule (H2O). The amount of this gaseous oxygen which water can dissolve depends on the partial pressure of oxygen and the temperature of the water. In order to understand the expression “partial pressure” we have to deal first with the term “atmospheric pressure”. The pressure of the earth’s atmosphere, the “atmospheric pressure”, as in any fluid, changes with depth. But the earth’s atmosphere is somewhat complicated because not only does the density of air vary greatly with altitude, but there is no distinct top surface to the atmosphere from which the height of the air column (h) can be measured. The atmosphere extends from the earth to heights of thousands of kilometres, where it gradually merges with the solar winds. The air in the atmosphere consists of a mixture of gases, water vapour and minute solids and liquid particles in suspension. The bulk of the lower atmosphere (0 to 100 km) is composed mainly of N2 and O2, with a relative abundance of 0,78 N2 and 0,21 O2, based on the average number of molecules present in a representative volume of air. The mass of the hypothetical mean molecule of air of the lower atmosphere is 28,97 g/mol. This value is intermediate between that of N2 (28) and that of O2 (32) and reflects the presence of trace quantities of water, argon, carbon dioxide and other less abundant compounds (see table “Composition of the Atmosphere” overleaf).

Graph 1: Average molecular mass of the atmosphere in atomic units

This composition of the atmosphere is measured by its mean density (the average mass per unit volume). As it can be seen from the adjacent diagram, the mean density of air (28,97 grams per mole) does not change significantly from the earth’s surface to a height of about 100 km. Thereafter it reduces gradually down to less than 3 grams per mole at a height of 1 000 km.

The state of approximate uniformity in the first 100 km of height above the earth surface arises as a result of molecular motion and as a consequence of the high frequency with which molecules of a particular species are involved in collisions with their neighbours. For instance, an oxygen molecule, O2, encounters a nitrogen molecule, N2, on average once every 10-9 second near the earth surface. At heights of 100 km, the encounter time is reduced to about 10-3 second. Due to their molecular masses, molecules experience a force of gravity. Heavy gases are attracted more closely to the earth surface, whereas lighter gases are free to float higher. Oxygen gives way to helium above 600 km, and hydrogen is the major constituent at altitudes higher than 1 000 km.

Page 13

Composition of the Atmosphere

Table 1: Composition of the Atmosphere

Page 14 The atmospheric pressure is a force per unit area exerted by an atmospheric column. This is the entire body of air above the specific area. This column consists of the whole air composition and represents the sum of the “partial pressures” of all the individual air components. It is not possible to measure the height of the air column as explained before, but with the following formula the approximate difference in pressure between two altitudes can be calculated.

ΔP = ρ • g • Δh where:

(1)

P = air pressure ρ = mean density of air column g = acceleration of gravity h = height of air column

The pressure of the air at a given place varies slightly according to the weather. At sea level, the pressure of the atmosphere on the average is

1,013 • 105 N/m2. This value is used to define another unit of pressure in common use, the atmosphere (atm): 1 atm = 1,013 • 105 N/m2 = 101,3 kPa

(2)

Another unit of pressure sometimes used (in meteorology and on weather maps) is the

bar, which is defined as 1 bar = 1,00 • 105 N/m2 = 100 kPa

Thus standard atmospheric pressure is slightly more than 1 bar. The pressure due to the weight of the atmosphere is exerted on all objects with which it is in contact, including the human body. As 1 bar pressure represents the weight of a 10 m column of water we can imagine what enormous pressure our bodies are exposed to. How does a human body withstands this immense pressure on its surface? The answer is that living cells maintain an internal pressure that closely equals the external pressure, just as the pressure inside a balloon only slightly exceeds the outside pressure of the atmosphere.

(3)

Page 15 In 1663, Otto von Guericke (1602-1686), a German physicist, engineer, and natural philosopher, demonstrated the tremendous force of the atmospheric pressure which is exerted an a body. He manufactured two copper hemispheres with tight-fitting flanges and joined, but not fastened, them together with a leather gasket between them, to form a hollow sphere of about 355 mm in diameter. Guericke removed the air from the sphere (through a valve), the atmospheric pressure compressed the two hemispheres one against the other. Two teams of eight horses each were then harnessed to the hemispheres. These 16 horses were unable to pull the hemispheres apart even though the sphere was held together only by the air around it. Once air was admitted to the hemispheres, they fell apart instantly.

This famous experiment was performed before the Emperor Ferdinand III at Regensburg, Germany.

6. Pascal’s Principle The earth’s atmosphere exerts a pressure on all objects with which it is in contact, including other fluids. External pressure acting on a fluid is transmitted throughout that fluid. Example: What is the magnitude of water pressure at a depth of 35 m below the surface of the sea? P=ρ·g·h = (1 000 kg/m3) · (9,8 m/s2) · (35 m) = 343 000 N/m2 = 343,00 kPa However, the total pressure at this point is due to the pressure of water plus the pressure of the air above it. Hence the total pressure is 343,00 kPa + 101,3 kPa = 444,30 kPa This is just one example of a general principle attributed to the French philosopher and scientist Blaise Pascal (1623 – 1662).

Page 16 Pascal’s principle states that

Pressure applied to a confined fluid increases the pressure throughout by the same amount.

Conversion Factors Between Different Units of Pressure

Table 2: Conversion Factors between Different Units of Pressure

7. Saturated Vapour Pressure Air normally contains water vapour (water in the gas phase) which comes mainly from evaporation. The process of evaporation can be explained on the basis of kinetic theory. The molecules in a liquid move past one another with a variety of speeds. There are strong attractive forces between these molecules, keeping them together in the liquid phase. A molecule in the upper regions of the liquid may, because of the speed, leave the liquid momentarily. The combined attractive force of the other molecules can pull the escaping molecule back to the liquid surface if the velocity of this molecule is not too large. A molecule with a sufficiently high velocity, however, will escape from the liquid entirely into the gas phase. The amount of molecules having a kinetic energy above a particular value, to enable them to escape into the gas phase increases with temperature. In a closed glass vessel, filled partly with water (or any other liquid) and from which the air has been removed, the fastest moving molecules quickly evaporate into the space above. As they move around, some of these molecules strike the liquid surface and again become part of the liquid phase; this is one form of condensation. The number of molecules in the vapour (gas phase) increases for a period of time, until the number returning to the liquid equals the number leaving in the same time interval. Equilibrium then exists, and the vapour is said to be saturated.

Page 17 The pressure of the vapour when it is saturated above the liquid surface is called the Saturated Vapour Pressure. The saturated vapour pressure does not depend on the volume of the container. If the volume above the liquid were reduced suddenly, the density of molecules in the vapour phase would be increased temporarily. More molecules would then return back to the liquid phase until equilibrium is reached again. This would result in the same value of saturated vapour pressure as before. The saturated vapour pressure of any substance depends on temperature. At higher temperatures, more molecules have sufficient kinetic energy to break from the liquid surface into the vapour phase. Hence equilibrium will be reached at a higher pressure.

Table 3: Saturated Vapour Pressure of Water (at different temperatures)

Page 18

8. Partial Pressure 8.1 Dalton’s Law John Dalton was born on the 6th of September 1766 in Eaglesfield, Cumberland, England. He was the son of a Quaker weaver. When he was only 12 years old he took charge of a Quaker school in Cumberland and two years later taught with his brother at a school in Kendal. At 26 he officially became a teacher of mathematics and natural philosophy at a Presbyterian College in Manchester. He held this position until 1800, when he resigned to become the secretary of the Manchester Literary and Philosophical Society. He still served as a private teacher in mathematics and chemistry. John Dalton died on the 27th of July 1844. Dalton is well-known for the revival of the atomic philosophy, transforming it from a hypothesis into a scientific theory: “Each element is composed of tiny, indestructible particles, atoms, all alike and having the same atomic weight. Different elements have atoms of different weights. Each element therefore is characterized by the weight of its atom.” At the turn of the century Dalton turned his interest to chemistry although he had no experience in chemical research. In 1801 his early studies on gases led to the development of the law of partial pressure - known as Daltons Law: “The total pressure of a mixture of gases or vapours is equal to the sum of the partial pressures of the individual component gases, i.e. the sum of the pressures that each component gas would exert if it were present alone and occupied the same volume as the mixture of gases.” Strictly speaking, the principle is true only for ideal gases. It assumes no chemical interaction between the component gases. An ideal gas is a hypothetical gas that would consist of molecules that occupy negligible space and have negligible forces between them. All collisions made between molecules and the wall of a container or between molecules and other molecules would be perfectly elastic, because the molecules would have no means of storing energy except as translational kinetic energy. Dalton’s Law is approximately valid for real gases at sufficient low pressure and high temperature. Determining dissolved oxygen Dalton’s Law is applicable up to a maximum pressure of 600 kPa. 8.2 Partial Pressure Atmospheric air is a mixture of several kind of gases (see page 13). According to Dalton’s Law the atmospheric pressure is the sum of all vapour pressures of each individual type of gas. The pressure contribution of each kind of gas towards the total atmospheric pressure is called

the partial pressure of that gas. Dry atmospheric air contains and

78,1 % Nitrogen (N2) 20,95% Oxygen (O2) by volume.

It follows that 78,1 % of the atmospheric pressure can be attributed to the partial pressure of N2 and 20.95 % to the partial pressure of O2.

Page 19 At an atmospheric pressure of 101,3 kPa at sea level (1 atm) oxygen exerts a partial pressure POXYGEN = 21,22 kPa and nitrogen PNITROGEN = 79,12 kPa The partial pressure of oxygen may be calculated using the following formula: POXYGEN = XOXYGEN • PAIR where XOXYGEN PAIR

(4)

= 0,2095 (20,95 % by volume of O2 molecules in air) = total absolute air pressure

8.3 Absolute Pressure The absolute atmospheric pressure depends on the altitude. At sea level the absolute pressure is 101,3 kPa and it decreases approximately by 1,2 kPa per 100 m. This relationship is defined by the “barometric-altitude equation”:

Pa = Ps • 10 where

Pa Ps A C

= = = =



a c

(5)

absolute atmospheric pressure at altitude “a” in kPa atmospheric pressure at sea level in kPa (101,3 kPa) altitude, in km above sea level constant (18,4 km)

Table 4: Altitude versus Atmospheric Pressure

9. Oxygen Concentration in Water If oxygen-free water comes in contact with atmospheric air the water tries to draw oxygen molecules (and of course molecules of other gases) from the air until it reaches saturation. By doing so the water dissolves the oxygen gas like any other solid or liquid. The solubility depends on temperature: for solids and liquids solubility increases with rising temperature for gases solubility decreases with rising temperature.

Page 20 The increasing temperature provides the kinetic energy for the acceleration of all gas molecules. Some gas molecules escape from the water back into the air. This is the reason why a glass of beer goes flat when it gets warm and why fish will seek deeper water in summer because they cannot survive in the oxygen-starved warm water at the water surface. The dissolved oxygen exerts the same partial pressure in water as it does in air. The in-and-out movement of oxygen molecules at the air/water phase boundary stops when the partial pressure of oxygen in water equals the partial pressure of oxygen in air above the water. The water is now saturated with oxygen and a state of equilibrium is reached at the phase boundary air/water.

(6) From the above it can be seen that only the partial pressure of oxygen in air above the water determines the maximum partial pressure of oxygen in water. Not only oxygen molecules leave the water - also water molecules. Furthermore nitrogen molecules , argon molecules etc. also diffuse into air. The total partial pressure is therefore spread amongst all gases and vapours which are contained in air; the volume concentration of oxygen (20,95%) is not effected. Therefore the air above the water/air phase boundary is always moist to the extend that the air is water vapour saturated. Moist air behaves different to dry air and therefore the formula (4) POXYGEN = XOXYGEN • PAIR which is valid only for dry air. The formula has to be re-written to include the water vapour: PO2 = XO2 •(Pair - Pwater) where

PO2 XO2 Pair Pwater

= = = =

(7 )

partial O2 pressure in water vapour saturated air 0,2095 total atmospheric pressure partial water vapour pressure

Saturated water vapour pressure varies with temperature (see page 17, Table 3), therefore the partial oxygen pressure is temperature dependent.

Page 21 Example: What is the partial pressure for oxygen in water vapour saturated air at sea level and at an air temperature of 20 ºC?

PO2 = XO2 • (Pair - Pwater) = 0,2095 • (101,3 - 2,33) = 0,2095 • 98,97 PO2 = 20,73 kPa This value is approximately 2,3% below the value for dry air (21,22 kPa). With formula (7) we can calculate the oxygen concentration of air saturated water in units of the partial pressure of oxygen, i.e. in kPa. But industry very often requires the oxygen concentration in mg/l or ppm instead of kPa. The oxygen concentration in any liquid depends on the solubility of oxygen in that liquid and is proportional to the partial pressure of oxygen. The conversion from partial pressure to concentration is possible with the aid of “Henry’s Law”. The British physician and chemist William Henry (1775 - 1836) stated in 1803 that “When the temperature is kept constant, the weight of a gas that dissolves in a liquid is proportional to the pressure exerted by the gas on the liquid, provided that no chemical action occurs.” Henry’s Law describes how many litres of a gas dissolves in 1 litre of water at a certain temperature and a partial pressure of “P”:

S= where

S = P = PN = α =

P •α PN

(8)

solubility of the gas (by volume) the partial pressure of the gas atmospheric pressure (1 atm) 101,3 kPa absorption coefficient (dimension less) acc. to Bunsen

In the case of air saturated water the partial pressure of oxygen for water saturated air has to be substituted for “P”. The absorption coefficient “α” changes with every liquid analysed - therefore: different solutions have a different dissolved oxygen concentration at the same partial pressure of oxygen. Atmospheric pressure 101,3 kPa and a temperature of 25 °C

Partial pressure of oxygen = 20,73 kPa Oxygen concentration at air saturated liquids:

= 8,26 mg/l

= 2 mg/l

= 5 mg/l

= 58 mg/l

Page 22 The absorption coefficient “α” is temperature dependent!

Table 5: α-values for Oxygen in Water With Henry’s Law, the molar mass (MO2) and the molar volume (VO2) of oxygen, it is possible to calculate the saturated oxygen concentration (mg/l) in air saturated water (water in equilibrium with air).

XO2 • (Pair _Pwater ) M CO2 = • α • O2 mg / l PN VO2 where CO2 XO2 Pair Pwater PN α MO2 VO2

= = = = = = = =

(9)

saturated oxygen concentration 0,2095 total atmospheric pressure partial water vapour pressure atmospheric pressure (1 atm) 101,3 kPa absorption coefficient (dimension less) acc. to Bunsen molar mass of oxygen (32 g/l) molar volume of oxygen (22,414 l/mol)

The values of the saturated oxygen concentration at different temperatures and different pressures play an important role for the calibration of dissolved oxygen analysers. Therefore these values are combined in

“Saturated Oxygen Concentration Tables”. Basically, the values of these tables cannot be determined by calculation, they have to be empirically established. As the saturated oxygen concentration in water depends on atmospheric pressure and temperature, samples of air saturated water at stable air pressure and at various temperatures have to be produced and their oxygen concentration determined. This is normally done by an iodometric Winkler titration in a laboratory. Various “Saturated Oxygen Concentration Tables” exist with slightly varying values. In Europe the DIN 38 408 table, published in 1986 is generally used. The reference for the atmospheric pressure is 101,3 kPa (“DIN” stands for “Deutsche Industrie Norm”, which is the German Industrial Standard).

Page 23

Saturated Oxygen Concentration Table acc. to DIN 38 408 (1986)

Table 6: Saturated oxygen concentration (mg/l) in air saturated water at a water

saturated atmospheric pressure of 101,3 kPa and varying temperature

Page 24 The DIN Saturated Oxygen Concentration Table is based only on one atmospheric pressure (101,3 kPa), a calculation is therefore required to establish the saturated oxygen concentration at the actual atmospheric pressure. This is done with the aid of formula (10):

C O 2 (Pair )

where

CO2(Pair) = CO2(P ) = Pair = Pwater = PN = N

(Pair _Pwater ) = • C O 2 (PN )mg / l (PN _Pwater )

(10)

saturated oxygen concentration at actual atmospheric pressure saturated oxygen concentration at 101,3 kPa actual atmospheric pressure partial water pressure standard atmospheric pressure (1 atm) 101,3 kPa

Example: What is the saturated oxygen concentration at an actual atmospheric pressure of 96,2 kPa and a temperature of 20 °C?

C O 2 (Pair )

(Pair _ Pwater ) = • C O 2 (PN )mg / l (PN _ Pwater ) =

96 ,2 _ 2 ,33 • 9 ,08 101,3 _ 2 ,33

= 8,61 mg/l Until now we have only discussed oxygen saturated water, i.e. water which has dissolved a maximum amount of oxygen, which it theoretically can take up. In this water the same partial pressure of oxygen prevails as in the water-saturated air above the water surface. But it is quite possible that the oxygen concentration in water can be higher or lower than its saturation level, that means that the equilibrium of the partial pressure of oxygen between air and water no longer exists. Waters not in equilibrium may be very stable in reference to their oxygen concentration. They will of course either loose oxygen to the air or gain oxygen from the air, whatever the case may be, but these diffusion processes are very, very slow. In order to determine the saturation condition for oxygen of these waters the so-called

Oxygen Saturation Index “s” can be applied. This oxygen saturation index specifies the percentage of the actual oxygen concentration in relation to the saturation value CO2.

s= where

s C C02

C • 100% CO2

= oxygen saturation index = actual oxygen concentration = saturated oxygen concentration

(11)

Page 25

Example: What is the oxygen saturation index, if water at 20 °C and at an atmospheric pressure of 98 kPa contains 7,12 mg/l oxygen? A) Initially the saturated oxygen concentration at 98 kPa has to be calculated:

C O 2 (Pair ) =

=

(Pair _Pwater ) • C O 2 (PN )mg / l (PN _Pwater )

98 _ 2 ,33 • 9 ,08 101 ,3 _ 2 ,33

= 8,78 mg/l B) the oxygen saturation index may now be calculated:

s=

C • 100% CO2

s=

7,12 • 100% 8,78

= 81,1% It is important to note that the same mass concentration of oxygen in water, but at different temperatures, will result in different saturation indexes, i.e. the above example at 35 °C would result in a saturation index of 106 %.

10. Oxidation - Reduction (redox) Originally, oxidation was simply regarded as a chemical reaction with oxygen. The reverse process - loss of oxygen - was called reduction. Oxidation and reduction processes occur continuously in nature. Most metals are oxidized directly by free oxygen; for example, iron reacts in accordance with the equation: 2 Fe + O2 → 2 FeO Ferrous oxide (FeO) can also be oxidized further to ferric oxide (Fe2O3): 4 FeO + O2 → 2 Fe2O3 This oxidation reaction may also take place in aqueous solutions, where certain substances form ions: 4 Fe2+ + 2 H2O + O2 → 4 Fe3+ + 4OH– whereby the ferrous ion (Fe++) loses an electron to the oxygen, thus becoming the ferric ion (Fe+++), hence passing from the bi-valent to the tri-valent state. The last oxidation example leads us to today’s more wider definition of oxidation and reduction which is universally accepted and independent from the element oxygen:

Page 26

Oxidation takes place when a molecule or ion loses electrons Reduction takes place when a molecule or ion gains electrons However, since free electrons hardly exist in any solution, reduction and oxidation reactions are always coupled together. It is the movement of electrons that causes both oxidation and reduction: one reaction releases just as many electrons via oxidation as the other one consumes via reduction. These simultaneous and complimentary reduction and oxidation processes are generally called “redox” reactions. A simple example of a redox reaction is the combination of hydrogen with oxygen to form water:

2 H2 + O2 → 2 H2O The hydrogen is oxidized and the oxygen is reduced.

11. The Measuring Principle In order to determine the oxygen concentration in water a polarographic sensor is commonly used. The dissolved oxygen will be reduced at the surface of a noble metal electrode, the working electrode, acting as a cathode:

O2 + 2 H2O + 4 e– → 4 OH– A silver/silver chloride counter electrode, the anode, releases the required electrons:

4 Ag → 4 Ag+ + 4 e– This electron flow from the anode to the cathode represents the measuring signal which is proportional to the partial pressure of oxygen in the measured solution. The above decribed chemical reaction does not start automatically, but has to be imposed by an applied voltage which has to have at least the magnitude of the standard redox potential (+401 mV) of the reaction at the cathode, but with reversed polarity. This negative voltage, the polarisation voltage, must be absolute constant and has to be stabilized against a reference electrode.

Page 27 The standard redox potential is measured against the standard hydrogen electrode; the utilised Ag/AgCl reference electrode itself has a potential difference of +210 mV against the standard hydrogen electrode. The applied polarisation voltage must therefore be the sum of both voltages: – (401 + 210) = –611 mV. This is only an indication value, as it will be seen later - the actual applied polarisation voltages are much higher. If the applied polarisation voltage is too low, lets say below –200 mV, no oxygen reduction will take place at the cathode. The voltage has to be raised above that value in order that the reduction will start Graph 2: Composition of polarisation voltage and electrons are consumed at the cathode. This will initiate an electron flow from the anode to the cathode, resulting from the oxidation at the anode which will release the required electrons. The current will increase steeply until a plateau is reached at approximately –600 mV. Even if we increase the voltage any further the current will not raise significantly. The chemical reaction is now so fast that all oxygen molecules at the cathode are reduced and the resulting electron flow - the measuring current - is only dependent on the oxygen concentration in the measured solution (see the diagram below).

Graph 3: Diffusion Plateau At the “Partial Reduction Zone” the polarisation voltage is insufficient to enable a total reduction of all oxygen molecules at the cathode. At the “Diffusion Plateau” the current no longer depends on the polarisation voltage. All oxygen molecules at the cathode are reduced. The current is proportional to the quantity of oxygen molecules in the sample solution. The “Operating Point” should be positioned at the middle of the diffusion plateau.

Page 28 The oxygen concentration at the working electrode (cathode) is, strictly speaking, not representative to the oxygen concentration in the sample solution. Oxygen molecules are constantly reduced and therefore the oxygen concentration decreases continuously at the cathode. To overcome this problem the measured solution has to be stirred, which always delivers fresh oxygen molecules to the working electrode and by that, makes the oxygen concentration at the cathode representative to the sample solution. But there will always be a small unstirred boundary layer at the cathode surface, no matter how strong the stirring action. Only by diffusion can the oxygen molecules reach the cathode surface, the electron flow is thereby governed by this diffusion, the current at the plateau is therefore called “Diffusion Current ID”.

12. The Membrane-covered Clark Dissolved Oxygen Sensor Before 1956 dissolved oxygen sensors consisted of bare, un-insulated noble metal electrodes. These sensors had a big drawback as they were quickly coated with the measured medium which negatively influenced the measuring result. It was the American scientist Leland C. Clark (1918 - 2005) who invented a polarographic oxygen sensor which consisted of two electrodes, a silver anode and a platinum cathode which are both immersed into half-saturated KCl-electrolyte. The electrolyte chamber is separated from the sample solution by a Teflon membrane which is held in place by a rubber ring. Oxygen molecules from the sample solution diffuse through the membrane into the electrolyte. The platinum cathode is completely insulated by a glass cylinder and only the tiny tip, having a diameter of approximately 20 μm, is exposed to the electrolyte. The electron flow between the two electrodes, when polarized with a negative potential of –600 mV, determines the oxygen concentration in the measured medium. U

I DO Meter Cathode Glass insulation

Medium

Electrolyte Reference and Anode Membrane

O2 O2

O2

O2

The Clark Dissolved Oxygen Sensor

Page 29 The oxygen sensor developed by Clark is a “two electrode sensor”, i.e. the anode is combined with the reference electrode. To fulfil the task as a reference the anode has to be coated with silver-chloride (AgCl) or with silver-bromide (AgBr). The electrolyte, which surrounds the anode, must also contain the coating material.

cathode membran

O2 O2

O2

O2

The most important development of the Clark oxygen sensor is the protection of the electrodes from the measured medium by a membrane. This membrane must have the ability to allow oxygen to diffuse through it from the measured medium to the cathode. Membrane material is normally PTFE or FEP, having a thickness of between 10 to 50 μm. These plastics possess a high oxygen permeability, are highly resistant to chemical corrosion and can be exposed to relative high temperature. The membrane has to be fitted to the sensor in such a manner that it will lie flat against the cathode tip in order that all diffused oxygen will be reduced.

The membrane-covered Clark sensor constantly requires a flow of new sample solution in order to supply oxygen molecules to the sensor cathode. If the reduction at the cathode is low the flow velocity can also be low, but if the reduction is fast, the flow velocity of the measured medium has to be increased accordingly. The oxygen consumption at the cathode depends on the thickness of the membrane and the size of the cathode tip area: a)

the thicker the membrane the smaller the oxygen consumption combined with a slower response time

b)

the smaller the cathode tip area the smaller the oxygen consumption

By the variation of these parameters to their optimum it is possible to slow the flow velocity of the measured medium down to less than 5 mm/sec. But contrary to this, the oxygen sensor should have a fast response time which requires a thin membrane (approximately 10 μm). The oxygen consumption at the cathode again depends on the thickness of the membrane and the size of the cathode tip area; therefore a thin membrane requires a high flow velocity of the measured medium of up to 300 mm/sec. The measuring signal, which is the electron flow between anode and cathode, is mathematically expressed by the following equation:

I = n • F • PM •

PO2 •A b

(12)

where:

I n F PM PO2 b A

= = = = = = =

measured signal number of electrons released by the chemical reaction (n = 4) Faraday’s constant (9,649 • 104A • s • mol –1) Oxygen permeability of the membrane Partial pressure of oxygen Membrane thickness Area of cathode tip

Page 30 From the above formula it can be seen that the measured signal is directly proportional to the partial pressure of oxygen and not to the oxygen concentration. If the measured value must be displayed in ppm, ppb or mg/l, the temperature of the sample fluid, the barometric pressure and the oxygen solubility of the measured media must be known. A separate temperature probe can be used, but most oxygen sensors have a built-in temperature probe. A solubility table for oxygen in water (see page 23) is normally included in the software of modern dissolved oxygen meters (DO meters), and even a barometric pressure sensor is part of the hardware of these meters. The membrane’s permeability is also temperature dependent. The oxygen permeability of the membrane increases strongly with rising temperature. In other words, increasing permeability at higher temperature allows more oxygen to diffuse into the electrolyte of the oxygen probe, even though the oxygen partial pressure has not changed. This would result in a rise of the measuring current and gives false measuring results if not compensated for with a temperature measurement near the membrane. The temperature dependency of the oxygen diffusion “PM” is explained by the following formula:

(13)

where:

PM PStp E R T

= = = = =

Oxygen permeability of the membrane Oxygen permeability at standard condition Initiation energy Gas constant Absolute temperature

The measuring current increases exponentially when the temperature of the membrane rises. The temperature dependency of the membrane is normally given as the “membrane temperature coefficient” and can be compensated for by the measuring converter via the temperature probe.

13. Calibration Not every dissolved oxygen sensor supplies the same measuring current for a given oxygen partial pressure. Each sensor differs slightly in its physical characteristics and its material composition, its slight membrane differences and its electrolyte consumption, which again results in slight variations of the measuring current. As with pH electrodes, the measuring current of dissolved oxygen sensors also decrease slowly with time, due to the aging of the electrolyte, therefore each sensor has its own individual measuring slope:

“nA per partial pressure of oxygen”. For a sufficient high measurement accuracy the output of the measuring converter has to be adapted (calibrated) to the sensor zero current and slope at regular intervals.

13.1 Sensor Zero Calibration The zero current of the oxygen sensor at 0 mbar oxygen partial pressure has to be calibrated first. Normally the zero current is negligibly small and almost identical with the converter zero point. Nevertheless the sensor zero current should be periodically checked, especially before the measurement of low oxygen concentrations.

Page 31 Zero-point calibration may be effected either in pure nitrogen or in water saturated with nitrogen. A further alternative is the use of a freshly-prepared 2% bisulphite solution. In any case the sensor tip must be exposed to 0% oxygen. The saturation of water with nitrogen takes several minutes. Calibration with pure nitrogen gas is faster and more reliable. The nitrogen gas must flow over the sensors tip. The zero-point can be read after approximately 2 - 3 minutes. The zero-point calibration may very often be omitted, as today's oxygen sensors are “zero current free”, but it should be performed at least at the “first-time calibration”. As today’s DO converters are mostly microprocessor-based, they have the ability to store the oxygen sensor data as reference values for sensor statistics. These are the deviations of slope and zero-point, corresponding calibration values for temperature, air pressure, response time, calibration date and time, all with respect to the reference values of the first-time calibration. A first-time calibration has to be performed each time when either the complete sensor, the electrolyte, or the membrane with electrolyte is replaced.

13.2 Sensor Slope Calibration The slope calibration can be performed either in water, in air or with a calibration solution where the oxygen concentration is known.

13.2.1 Calibration in Water Water calibration is usually effected in 100% air-saturated water, i.e. the water must be in equilibrium with air. Oxygen exchange between water and air is normally very slow. In order to speed the saturation process up, air may be forced into water by a small fish-tank pump or with the aid of a compressed air bottle. Care has to be taken that the air inlet does not take place too deep below the water surface and the air velocity is not too fast, as the air might be compressed by the water column and bubbles may appear. A higher partial oxygen pressure, different to the partial oxygen pressure above the surface is the result. Another requirement is an absolute constant water temperature during the calibration time. Water temperature might be influenced by changing room temperature and by the cooling effect of the forced air intake. Stabilizing will take much time. It follows that it is very difficult to produce air saturated water with an accuracy better than 1 to 2%. Modern DO converters include a small barometric pressure sensor. As explained previously, the oxygen sensor incorporates a temperature probe. Pressure and temperature is therefore always known and the microprocessor automatically does the necessary calculations for ambient pressure and temperature compensation for membrane permeability and water solubility. The calibration water must be stirred to achieve the minimum required flow velocity, the water temperature and pressure conditions should correspond as closely as possible to those expected to be encountered during the actual measurement.

13.2.2 Calibration in Air Preferably the slope calibration should be done in air. It is easier to produce water vapour saturated air than air saturated water. The partial pressure of oxygen, as explained previously , is the same above the water level and just under the water level. A water bottle filled partly with water and left alone approximately for 15 minutes provides 100% water vapour saturated air. It is important to keep the tip of the oxygen sensor dry, condensed water drops at the membrane influences the oxygen diffusion through the membrane and falsifies the electron current.

Page 32 Parameters like temperature and pressure must remain constant during calibration. With modern microprocessor DO meters it is no longer required to perform the air calibration in water vapour saturated air. An input is provided to manually enter the ambient relative air humidity in %. The calibration is set to 100% saturation index. The meter calculates the partial pressure of oxygen at the set relative humidity and adds the missing partial pressure of the water vapour. The result will be an indication of 100% saturation index either just above a water surface or just under the water surface. The measuring result in ambient air will be higher than 100% as the partial pressure of oxygen in ambient air will be higher because of the missing water vapour.

air with rH= 50 %

air with rH= 50 %

100.0 %

101.2 %

calibration mode

measurement mode in ambient air

100.0 %

measurement mode in oxygen saturated water

The partial pressure of oxygen in partly water vapour saturated air can be calculated with formula (14):

PO2” = XO2 (Pair - h • Pwater)

(14)

where:

PO2” XO2 Pair Pwater h

= = = = =

partly water vapour saturated air 0,2095 total atmospheric pressure partial water vapour pressure relative humidity in %/100

Example: What is the saturation index indication of a DO meter in ambient air at 20 °C, 101,3 kPa atmospheric pressure and a relative humidity of 50%?

PO2” = XO2 (Pair - h • Pwater) = 0,2095(101,3 - 0,5 • 2,33) = 0,2095(101,3 - 1,165) = 0,2095 • 100,135 PO2” = 20,98 kPa

Page 33 20,73 kPa was the calculated value for the partial pressure of oxygen in water vapour saturated air at equal conditions (formula 7, page 21). The percentage difference can then be calculated as follows: PO 2 " 20 ,98 = • 100 = 101,2 % PO 2 20 ,73

13.2.3 Calibration with a Calibration Solution The calibration procedure with calibration solutions where the oxygen concentration is known is easy and similarly to the calibration with air saturated water. The oxygen sensor has to be immersed into the calibration solution and the known concentration value has to be entered into the DO converter after the indication value of the meter’s display has stabilised.

14. Influence of Salinity If a Winkler-Titration is done on air saturated freshwater and, for comparison sake, on air saturated seawater, both under identical conditions (temperature and barometric pressure), it will be noticed that the oxygen concentration (mg/l) in seawater will be approximately 20% lower than it is in freshwater. If these measurements are repeated with a Clark sensor, both measurements will render identical results, as the membrane covered oxygen sensor responds only to the partial pressure of oxygen. The partial pressure of oxygen in both, freshwater and seawater under identical conditions, is the same, as it is only governed by the air above the water surface. It follows that saltwater does not require so much oxygen to establish an equilibrium in the partial pressure of oxygen at the phase boundary air/water (see page 20). The solubility of oxygen in water is reduced by the salt content in that water and a dissolved oxygen measurement with a Clark sensor does not detect this fact. An accurate dissolved oxygen concentration measurement with a Clark sensor is possible if one can refer to a special Saturation Oxygen Table for Saltwater. Certain microprocessor based DO process meters have these so-called Oceanographic Tables, supplied by Unesco, integrated in their instrument software in order to calculated the correct oxygen concentration in seawater. The company KNICK incorporated various tables in their DO process meters to take account of the influence of the measured medium’s salt content on solubility:

Salinity to EN 25814 1992 International Oceanographic Tables, Unesco National Institute of Oceanography of Great Britain Volume 2, Wormley/Godalming/Surrey. The oxygen concentration can thus be corrected with the KNICK process meters via a salinity factor corresponding to the salt content of the measured medium. It is not possible to give a general guidance for the salinity correction when measuring the dissolved oxygen concentration in aqueous solutions. This depends mainly on the ability of the available process meters - their operating instructions have to be referred to.

15. The HAMILTON DO Sensors The Swiss company HAMILTON offers dissolved oxygen sensors for a wide field of applications. All sensors are quality products and manufactured in accordance with the latest scientific and technical knowledge. HAMILTON’s dissolved oxygen sensors are based on the Clark’s principle having two-electrodes, cathode and anode. The anode also serves as a reference electrode. Each type of sensor contains a 22 kΩ NTC thermistor for compensation of the temperature dependence of the membrane and the measured solution.

Page 34 HAMILTON offers three types of oxygen sensors:

1. OXYSENS 2. OXYFERM 3. OXYGOLD All three types have a 12 mm stainless steel shaft with varying immersion lengths. One of the outstanding feature of all three types is the OPTIFLOWTM membrane. This membrane features fast response times of 30 to 60 seconds combined with unusually low flow dependence. Although the membrane material is very thin (25 μm) it possesses an exceptional high mechanical strength due to a laminated wire mesh reinforced silicone layer (see picture below). 25 μm oxygen permeable Teflon

Approximately 150 μm silicon, wire mesh reinforced

Basi c construction diagram of HAMILTON oxygen sensors

Typical voltage/current curve s for HAMILTON oxygen sensors

The voltage between the anode and the cathode is selected so that the oxygen is fully reduced while other gases are unaffected. The ideal polarisation voltage for a platinum - silver/silver chloride electrode combination lies between –600 and –750 mV.

Page 35

15.1 The OXYSENS Dissolved Oxygen Sensor The OXYSENS was the first maintenance-free dissolved oxygen sensor on the market at an economical price. No membrane exchange is required. The expected lifetime is about two years. The OXYSENS is designed for applications in water treatment plants, swimming pools, fish farms and similar uses.

15.1.1 OXYSENS Technical Data Serial Number: Certificate: Measuring Method: Range: Current in air at 25 °C: Residual current in nitrogen: Response time t98%: Oxygen consumption: Required flow: Drift at room temperature under constant conditions: Max. CO2 partial pressure: Temperature sensor: Temperature response: Storage temperature: Working temperature: Pressure range: Pressure compensation: Electrode system: Membrane: Shaft diameter: Mounting: Electrical connector: Wetted materials: Surface quality of steel: Electrolyte: Polarization voltage: Stabilisation time: Steam sterilizable: Autoclavable: CIP: ATEX approval:

Yes Yes Measurement of the electrical current affected by the partial pressure of oxygen 40 ppb … 40 ppm of dissolved oxygen 40 … 80 nA < 0.5% (relative to current in air) Max. 60 s at 25 °C, from air to nitrogen Ca. 20 ng/h in air at 25 °C ≥ 0.03 m/s < 5% every 2 months at 25°C in water 0.01 bar NTC 22 kOhm 3.1%/K -10 … 60 °C 0 … 60 °C 0 … 4 bar Not required Silver platinum combination OPTIFLOW 12 mm PG 13.5 thread 5 meter fixed cable Stainless steel 1.4435, silicone, EPDM with FDA approval 0.4 μm OXYLYTE, alkaline -670 ± 50 mV < 1 hours No No No Yes, CE 0035 ll 1/2 G Ex ia llC T4/T5/T6

As the OXYSENS sensor is very often used in rivers, lakes and dams, hanging and supported by its cable, HAMILTON provides a stainless steel immersion and protection sleeve. This sleeve is provided with a PG 13.5 female thread into which the OXYSENS sensor is installed. The sleeve not only provides the weight for a quick and steady immersion, it also protects the sensor from mechanical damages. The immersion sleeve is illustrated by the adjacent picture.

Page 36

15.2 The OXYFERM Dissolved Oxygen Sensor The OXYFERM sensors are available in three different types: The FDA, the VP and the XL types. “FDA” stands for “Food and Drug Administration”. The FDA sensor incorporates a special rounded membrane body designed to FDA specification, the membrane consists of approved FDA membrane material and is sanitarily sealed to the stainless steel capsule. There is no gap between membrane and steel body, no additional o-ring has to be applied. The standard electrical connection of the FDA type is a T82/D4 bayonet fitting.

Sanitary Sealing

The VP type is the standard HAMILTON OXYFERM sensor and is characterized by its electrical connection - it features a VP 6.0 plug classified as IP 68. The OXYFERM XL is applied where a standard G 1¼” weld-in socket is present. The “OP-length” (O-ring position length) has to be specified, it may be between 22 mm and 55 mm. The main target for the OXYFERM sensors are the biotechnology and pharmaceutical industries. All OXYFERM sensors are suitable for steam sterilization (SIP), autoclavation and cleaning in process (CIP). The sensor’s outstanding feature is its long-term stability even when sterilized or autoclaved often.

VP 6.0 Plug

The graph below illustrates the excellent performance of OXYFERM sensors even after 100 sterilizations without the need for maintenance. Other types of oxygen sensors subject to the same conditions require maintenance after 5 to 10 sterilization cycles.

OXYFERM XL

Due to the improved design of the sensor, service cycles have been prolonged thus strongly reducing maintenance which in turn lowers operating costs. Each OXYFERM sensor comes with a material and performance test certificate showing the material melt number and the serial number of sensor and membrane. Other features include: Upside-down (USD) insertion (bottom of tank) with special USD electrolyte, replaceable inner glass body containing cathode and anode, a selection of membrane materials (standard, CIP and FDA) negligible drift, fast response and short polarisation time.

Page 37

15.2.1 OXYFERM FDA Technical Data Serial Number: Certificate: Measuring Method: Range: Current in air at 25 °C: Residual current in nitrogen: Response time t98%: Oxygen consumption: Required flow: Drift at room temperature under constant conditions: Max. CO2 partial pressure: Temperature sensor: Temperature response: Storage temperature: Working temperature: Pressure range: Pressure compensation: Electrode system: Membrane: Shaft diameter: Mounting: Electrical connector: Wetted materials: Surface quality of steel: Electrolyte: Polarization voltage: Stabilisation time: Steam sterilizable: Autoclavable: CIP: ATEX approval:

Yes Yes Measurement of the electrical current affected by the partial pressure of oxygen 10 ppb … 40 ppm of dissolved oxygen 40 … 80 nA < 0.1% (relative to current in air) Max. 60 s at 25 °C, from air to nitrogen Ca. 20 ng/h in air at 25 °C ≥ 0.03 m/s < 1% per week 0.01 bar NTC 22 kOhm 3.1%/K -10 … 60 °C 0 … 130 °C 0 … 4 bar Not required Silver platinum combination OPTIFLOW FDA 12 mm PG 13.5 thread Standard 4 pole T 82/D4 Stainless steel 1.4435, EPDM and silicone with FDA approval 0.4 μm OXYLYTE, alkaline -670 ± 50 mV < 2 hours Yes Yes Yes Yes, CE 0035 ll 1/2 G Ex ia llC T4/T5/T6

Pull

Replacing the cathode glass body is easy. For a detailed description refer to page 41.

15.3 The OXYGOLD Dissolved Oxygen Sensor Two types of OXYGOLD sensors are available: the OXYGOLD G and B types. These sensors are high-end dissolved oxygen detectors possessing outstanding features hardly found in any other sensor. The main application for the OXYGOLD G sensor is the detection of trace quantities of oxygen down to 1 ppb in power generation plants (e.g. boiler feed water), water treatment, semiconductor manufacturing, chemical and pharmaceutical industries. Demands on oxygen sensors in the beer brewing industry is high. They must detect oxygen accurately and reliably in a high CO2 environment, must possess stability at high pressures, have fast response and low detection limits combined with a minimum of maintenance. All these

Page 38 requirements are found in the OXYGOLD B sensor. Due to its CO2-stable acidic electrolyte the OXYGOLD B has no CO2 interference (detection limit in pure CO2 is < 8 ppb) and works under a permanent operating pressure of 1 200 kPa, even multiple vacuum and pressure peaks present no problem to the OXYGOLD B. The maintenance frequency is very low and the membrane replacement is easy. The HAMILTON OXYGOLD B sensor should always be the first choice in any brewery or beverage bottling plant. The OXYGOLD G sensor is suitable for steam sterilization in process (SIP) and cleaning in process (CIP), the OXYGOLD B sensor is only suitable for CIP.

15.3.1 OXYGOLD G Technical Data Serial Number: Certificate: Measuring Method: Range: Current in air at 25 °C: Residual current in nitrogen: Response time t98%: Oxygen consumption: Required flow: Drift at room temperature under constant conditions: Max. CO2 partial pressure: Temperature sensor: Temperature response: Storage temperature: Working temperature: Pressure range: Pressure compensation: Electrode system: Membrane: Shaft diameter: Mounting: Electrical connector: Wetted materials: Surface quality of steel: Electrolyte: Polarization voltage: Stabilisation time: Steam sterilizable: Autoclavable: CIP: ATEX approval:

Yes Yes Measurement of the electrical current affected by the partial pressure of oxygen 1 ppb … 40 ppm of dissolved oxygen 180 … 500 nA < 0.02% (relative to current in air) Max. 60 s at 25 °C, from air to nitrogen Ca. 100 ng/h in air at 25 °C ≥ 0.1 m/s < 1% per week 0.01 bar NTC 22 kOhm 3.1%/K -10 … 60 °C 0 … 130 °C 0 … 12 bar Not required Silver platinum combination OPTIFLOW 12 mm PG 13.5 thread VP 6.0 connector head Stainless steel 1.4435, silicone, EPDM with FDA approval, Gold < 0.4 μm OXYLYTE G, alkaline -670 ± 50 mV < 2 hours Yes Yes Yes Yes, CE 0035 ll 1/2 G Ex ia llC T4/T5/T6

Page 39

15.3.2 OXYGOLD B Technical Data Serial Number: Certificate: Measuring Method: Range: Current in air at 25 °C: Residual current in nitrogen: Response time t98%: Oxygen consumption: Required flow: Drift at room temperature under constant conditions: Max. CO2 partial pressure: Temperature sensor: Temperature response: Storage temperature: Working temperature: Pressure range: Pressure compensation: Electrode system: Membrane: Shaft diameter: Mounting: Electrical connector: Wetted materials: Surface quality of steel: Electrolyte: Polarization voltage: Stabilisation time: Steam sterilizable: Autoclavable: CIP: ATEX approval:

Yes Yes Measurement of the electrical current affected by the partial pressure of oxygen 8 ppb … 40 ppm of dissolved oxygen 180 … 500 nA < 0.1% (relative to current in air) Max. 60 s at 25 °C, from air to nitrogen Ca. 100 ng/h in air at 25 °C ≥ 0.1 m/s < 1% per week 12 bar NTC 22 kOhm 3.1%/K -10 … 60 °C 0 … 100 °C 0 … 12 bar Not required Silver platinum combination OPTIFLOW 12 mm PG 13.5 thread VP 6.0 connector head Stainless steel 1.4435, silicone, EPDM with FDA approval, Gold < 0.4 µm OXYLYTE B, acidic 0 mV < 24 hours Yes Yes Yes Yes, CE 0035 ll 1/2 G Ex ia llC T4/T5/T6

16. Stabilisation Time – Polarization Modules The stabilization time is the time between connection of the oxygen sensor to the converter (measuring instrument) and the time when accurate measurements can be expected. The reason is the following: Oxygen has diffused through the membrane into the electrolyte compartment of the sensor during the time when no voltage was applied to the sensor. This oxygen has to be consumed by the cathode first, the result is a temporarily high O2 concentration indication by the measuring instrument which is not a measuring result. The stabilization time depends on the sensor type and on the required measuring accuracy. Normally manufactures of oxygen sensors specify the stabilization time under the technical data of their sensors. As these times can range between 30 minutes and 24 hours the company HAMILTON has introduced so-called “Polarization modules” in order to prepare replacement oxygen sensors for immediate use once being connected to a measuring instrument. As the OXYGOLD B sensor differs from the HAMILTON Polarization Unit

Page 40 OXYGOLD G in its polarization voltage, there are two polarization modules available, one for all sensors having a polarization voltage of –670 mV, including the OXYGOLD G sensor and one for the OXYGOLD B sensor.

17. Maintenance of the HAMILTON Oxygen Sensors 17.1 OXYSENS The OXYSENS dissolved oxygen sensor is maintenance-free. It must be stored at temperatures between -10 °C and +60 °C with a water-filled cap covering the sensor tip. This cap must be removed before calibration and measurement. If the sensor cannot be calibrated anymore, it must be replaced.

17.2 OXYFERM The OXYFERM dissolved oxygen sensor must be stored at temperatures between -10 °C and +60 °C with a water-filled cap covering the sensor tip. This cap must be removed before calibration and measurement. The OXYFERM sensors are shipped dry with the exception of the FDA type, i.e. no electrolyte is in the membrane cartridge. The membrane cartridge has to be carefully unscrewed from the sensor body, pre-rinsed with the corresponding electrolyte and then filled with 1,5 ml of that electrolyte. Care must be taken not to touch or break the cathode/anode glass assembly. The filled membrane cartridge has to be screwed tightly to the sensor body. After connection to a measuring instrument (process converter, transmitter) the polarization voltage has to be set to −670 mV ± 50 mV. After a maximum period of 2 hours the sensor is ready for calibration. If the sensor is disconnected from the measuring instrument for a short time, the renewed polarization time must equal twice the disconnection time, but no more than 2 hours. During external sterilization the OXYFERM sensor’s bayonet plug T82/D4 should be covered by a protective cap (available from HAMILTON). If the plug is partially filled with water despite the protective cap, the plug should be rinsed with ethanol and dried afterwards with a hair dryer. No protection is necessary when using a VP 6.0 connection. An operational sensor check can be performend as follows: Calibrate the polarized sensor in air and adjust the measuring instrument to 100 %. Immerse the sensor in nitrogen gas (i.e. by using a bag filled with nitrogen). After the sensor is immersed for 1 minute in nitrogen the instrument must show a value below 2% of the previous value in air. If the value in nitrogen is too high the electrolyte might be exhausted or the membrane might be deformed or otherwise be defective. In such a case the electrolyte or the membrane cartridge and the electrolyte has to be replaced. If the sensor does still not calibrate well, i.e the response is to sluggish or the zero current is too high, the cathode and the front end of the glass body have to be cleaned with the polishing strip included in the membrane kit. After cleaning, the glass body must be rinsed under a running water tap and dried carefully.

Page 41 If the sensor problem still persists, the cathode has to be replaced. With the cathode the membrane also has to be exchanded to obtain the full performance of the sensor. The cathode assembly has to be replaced as follows: 1. Put the sensor in an upright position and carefully unscrew the membrane cartridge. 2. Flush the replaceable cathode assembly with deionised water and then dry the metal parts. Do not touch anode and cathode! 3. Hold the cathode assembly on the metal part (B) in front of the thread (A) and the sensor on the shaft (C) and pull apart. Do not turn! 4. Please check that all contacts are dry and clean. 5. Replace the cathode assembly for a new one (blue for OXYFERM, yellow for OXYGOLD B and black for OXYGOLD G). Rotate the cathode assembly slowly and carefully until the correct position is found and then push the cathode assembly into the sensor shaft. 6. Check the small O-ring (D) above the thread. Replace if damaged. 7. Use the 1 ml plastic pipette of the membrane kit to pipette 1,5 ml of electrolyte into the new membrane cartridge. The pipette must not touch the membrane itself! 8. Screw the cartridge onto the sensor shaft. Any spillage of electrolyte should be rinsed away with water.

17.3 OXYGOLD G & B The OXYGOLD dissolved oxygen sensor must be stored at temperatures between -10 °C and +60 °C with a water-filled cap covering the sensor tip. This cap must be removed before calibration and measurement. The OXYGOLD sensors are shipped dry, i.e. no electrolyte is in the membrane cartridge. The membrane cartridge has to be carefully unscrewed from the sensor body, pre-rinsed with the corresponding electrolyte (G or B) and then filled with 1,5 ml of that electrolyte. Care must be taken not to touch or break the cathode/anode glass assembly. The filled membrane capsule has to be re-screwed tightly to the sensor body. After connection to a measuring instrument (process converter, transmitter) the polarization voltage has to be set to −670 mV ± 50 mV for the OXYGOLD G sensor. After a maximum period of 2 hours the sensor is ready for calibration.

For the OXYGOLD B sensor the polarization voltage must be set to 0 mV. After a maximum period of 24 hours the sensor is ready for calibration. If this polarization time is considered too long, please refer to paragraph 16 - the purchase of a polarization module might be advisable.

Page 42

18. Connection to Various Process Meters/Converters/Transmitters As the HAMILTON dissolved oxygen sensors may be connected to most dissolved oxygen process meters on the market it is not possible to describe the process connections, calibration and measurement settings of these meters in this brochure. Please refer to the operating instructions supplied with these measuring instruments.

Theory is necessary – Experience is essential Have success with your Dissolved Oxygen Measurement!

http://www.hamiltoncompany.com [email protected] R

THE MEASURE OF EXCELLENCE

TM

Hamilton Bonaduz AG Via Crusch 8 CH-7402 Bonaduz/Switzerland Toll-Free: 00800-660-660-60 Telephone: +41-81-660-60-60 Fax: +41-81-660-60-70 [email protected]

Your HAMILTON representative:

Hamilton Company 4970 Energy Way Reno, Nevada 89520 USA Toll-Free: 800-648-5950 Telephone: +1-775-858-3000 Fax: +1-775-856-7259 [email protected] Quality Hamilton Products: Laboratory Electrodes Process sensors DURACAL™ pH buffer solutions Conductivity sensors Conductivity standards Oxygen sensors Retro-fit armatures for sensors MICROLITER™ syringes GASTIGHT® syringes Instrument syringes SoftGrip™ pipettes SofTouch™ pipettes SoftAide™ pipettes SofTop™ dispenser GC liner HPLC columns Precix GC columns Laboratory Automation for: Drug Discovery Genomics Proteomics Forensics In Vitro Diagnostics

E/624199/00 12/2008